Expansion Shield Anchor 3/8"
(Pack of
10)
Evenly distributed four-way expansion of anchor wall by internal nut
Excellent holding power in concrete, brick, stone and cinder block
Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
Meets GSA Specification FF-S-325 3.2.2.2.1.3
Use for anchoring medium and heavy loads in solid and hollow-base materials
Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Couldn't load pickup availability
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
Frequently Bought Together

Light-Medium Duty Anchor Assortment 555Pcs
Couldn't load pickup availability

Wallboard Anchor Assortment 1125Pcs
Couldn't load pickup availability

Hollow Wall Screw Anchor Assortment 196Pcs
Couldn't load pickup availability

Lag Screw Shield Anchor Short Style 1/4 x 1"
Couldn't load pickup availability

Expansion Shield Anchor 1/2"
Couldn't load pickup availability

Pin Drive Expansion Anchor Steel 3/4 x 6"
Couldn't load pickup availability

Open End Rivet Large Flange Head Aluminum 3/16"
Couldn't load pickup availability

Open End Rivet Dome Head Aluminum 3/16"
Couldn't load pickup availability

Hex Flange Bolt Grade 10.9 M8-1.25 x 40mm
Couldn't load pickup availability

Front Bumper Specialty Nut Steel M4.2-1.41
Couldn't load pickup availability

Hex Head Sheet Metal Screw with 16mm Washer Steel
Couldn't load pickup availability

Front Fender Push-Type Retainer Nylon 18mm
Couldn't load pickup availability
Product Description
Evenly distributed four-way expansion of anchor wall by internal nut Excellent holding power in concrete, brick, stone and cinder block
Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
Meets GSA Specification FF-S-325 3.2.2.2.1.3
Use for anchoring medium and heavy loads in solid and hollow-base materials
Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Technical Specifications
Item#: | 96960 |
---|---|
Anchor Size | 3/8 " |
Type | Forway Expansion Shield Anchor |
Drill Size | 11/16 " |
3,000 PSI Concrete Shear Strength | 3,850 lb |
Tensile Block | 2,440 lb |
Thread Pitch | 16 |
3,000 PSI Concrete Tensile Strength | 3,640 lb |
UNSPSC #: | 31162101 |
TAA Compliant: | Yes |
Weight: | 0.74 lb |
Product Restrictions
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
