Expansion Shield Anchor, 9/16" Drill Size, 5/16"
(Pack of
25)
SKU:96959 Item#: 96959
• Evenly distributed four-way expansion of anchor wall by internal nut
• Excellent holding power in concrete, brick, stone and cinder block
• Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
• Meets GSA Specification FF-S-325 3.2.2.2.1.3
• Use for anchoring medium and heavy loads in solid and hollow-base materials
• Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Frequently Bought Together
Masonry Anchor Assortment 243Pcs
Couldn't load pickup availability
Light-Medium Duty Anchor Assortment 555Pcs
Couldn't load pickup availability
Wallboard Anchor Assortment 1125Pcs
Couldn't load pickup availability
Lag Screw Shield Anchor Short Style 1/4 x 1"
Couldn't load pickup availability
Expansion Shield Anchor 1/2"
Couldn't load pickup availability
Pin Drive Expansion Anchor Steel 3/4 x 6"
Couldn't load pickup availability
Hex Flange Bolt Grade 10.9 M8-1.25 x 40mm
Couldn't load pickup availability
Hex Flange Bolt Grade 10.9 M10-1.25 x 25mm
Couldn't load pickup availability
Serrated Hex Flange Nut Alloy Steel M10-1.25
Couldn't load pickup availability
Fender Splash Shield Push Rivet Nylon 7mm Hole
Couldn't load pickup availability
Front/Rear Bumper Push-Type Retainer Nylon 20mm
Couldn't load pickup availability
Nylon Cable Tie 15-1/4" Black
Couldn't load pickup availability
Product Description
• Evenly distributed four-way expansion of anchor wall by internal nut• Excellent holding power in concrete, brick, stone and cinder block
• Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
• Meets GSA Specification FF-S-325 3.2.2.2.1.3
• Use for anchoring medium and heavy loads in solid and hollow-base materials
• Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Technical Specifications
| Item#: | 96959 |
|---|---|
| Anchor Size | 5/16 " |
| Type | Forway Expansion Shield Anchor |
| Drill Size | 9/16 " |
| 3,000 PSI Concrete Shear Strength | 3,300 lb |
| Tensile Block | 2,100 lb |
| Thread Pitch | 18 |
| 3,000 PSI Concrete Tensile Strength | 2,600 lb |
| UNSPSC #: | 31162101 |
| TAA Compliant: | Yes |
| Weight: | 1.06 lb |
