Cobalt End Mill, 4 Flute, Single End, Coarse Rougher, TiN Finish, 3/16" Diameter, 1/2" Cutting Length, 2-3/8" Overall Length
(Pack of
1)
SKU:14851 Item#: 14851
• M42 tool steel with an 8% cobalt content for long tool life and high heat and abrasion resistance for tough machining applications
• Made in USA
• TiN coating (Titanium Nitride) is ideal for a wide range of applications and cutting conditions where tool life and higher feeds and speeds are operating objectives
• High lubricity of TiN facilitates chip flow, prevents buildup and reduces cutting forces and temperature
• TiN reduces wear and improves chip formation to extend tool life
• Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates than conventional end mills. A rough finish is produced which will require a finishing pass
• Used in difficult and abrasive materials and tough alloy materials such as stainless steel, nickel base alloy, brass and iron
End Mill Selection: Harder workpieces require a higher number of flutes. Softer material requires fewer flutes.
CAUTION: Any cutting tool may break or shatter under improper use. Government regulations require use of safety glasses and other appropriate safety equipment at all times in the vicinity of use.
Frequently Bought Together
Jobber Length Drill Bit HSS 6.5mm
$0.00
Couldn't load pickup availability
Spot Weld Remover Drill Bit Cobalt 5/16" (M8)
$0.00
Couldn't load pickup availability
Abrasive Bristle Wire Belt Steel 23mm
$0.00
Couldn't load pickup availability
Solid Carbide End Mill 4 Flute Single End 1/4"
$0.00
Couldn't load pickup availability
Cobalt End Mill 4 Flute Single End 7/8"
$0.00
Couldn't load pickup availability
Cobalt End Mill 4 Flute Single End 1/2"
$0.00
Couldn't load pickup availability
Front/Rear Bumper Push-Type Retainer Nylon 20mm
$0.00
Couldn't load pickup availability
Bumper Clip Push-Type Retainer Nylon 18mm
$0.00
Couldn't load pickup availability
Front Bumper Trim Panel/Running Board Split Rivet
$0.00
Couldn't load pickup availability
Spinning Handmaster Driver Set 5Pc Set
$0.00
Couldn't load pickup availability
Universal Socket Set, Metric, 3/8" Drive, 12pc
$0.00
Couldn't load pickup availability
Small Index-Tend Pry Bar
$0.00
Couldn't load pickup availability
Product Description
• M42 tool steel with an 8% cobalt content for long tool life and high heat and abrasion resistance for tough machining applications• Made in USA
• TiN coating (Titanium Nitride) is ideal for a wide range of applications and cutting conditions where tool life and higher feeds and speeds are operating objectives
• High lubricity of TiN facilitates chip flow, prevents buildup and reduces cutting forces and temperature
• TiN reduces wear and improves chip formation to extend tool life
• Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates than conventional end mills. A rough finish is produced which will require a finishing pass
• Used in difficult and abrasive materials and tough alloy materials such as stainless steel, nickel base alloy, brass and iron
End Mill Selection: Harder workpieces require a higher number of flutes. Softer material requires fewer flutes.
CAUTION: Any cutting tool may break or shatter under improper use. Government regulations require use of safety glasses and other appropriate safety equipment at all times in the vicinity of use.
Technical Specifications
| Item#: | 14851 |
|---|---|
| Material | M42 |
| Finish | TiN |
| Center Cutting | Yes |
| Cutting Diameter | 3/16 " |
| Cutting Length | 1/2 " |
| Flutes | 4 |
| Shank Size | 3/8 " |
| Overall Length | 2-3/8 " |
| UNSPSC #: | 27112803 |
| TAA Compliant: | Yes |
| Weight: | 0.06 lb |
