Coolant Hose, 1/2" ID, 25/32" OD, 10' Length, 2-1/2" Bend Radius, 125PSI
(Pack of
1)
• EPDM tube and cover
• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Couldn't load pickup availability
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
Catalog page#: 7-10
Frequently Bought Together
Windshield Wiper Hose 9/32" ID x 50'
Couldn't load pickup availability
Standard Heater Hose 1/2" ID x 50' Black
Couldn't load pickup availability
NK1000063S150
Couldn't load pickup availability
DOT Connector Male Brass 1/4 x 1/8-27
Couldn't load pickup availability
Vacuum Hose Connector 3/16 x 3/16"
Couldn't load pickup availability
Slotted Hex Head Hose Clamp 301 SS 3/8 to 7/8"
Couldn't load pickup availability
H56908
Couldn't load pickup availability
H353H Truck Hose 33/64" OD x 250'
Couldn't load pickup availability
Silicone Heater/Coolant Hose Clamp SS 2-1/16 to 3"
Couldn't load pickup availability
Push-to-Connect Y Connector Nylon 1/4 x 1/8 x 1/4"
Couldn't load pickup availability
DOT Elbow Male Nylon 1/4 x 1/8-27
Couldn't load pickup availability
Slotted Hex Head Hose Clamp 301 SS 11/16 to 1-1/2"
Couldn't load pickup availability
Air Distributor Defroster Push-Type Retainer
Couldn't load pickup availability
Fender Splash Shield Push Rivet Nylon 7mm Hole
Couldn't load pickup availability
Front Fender Push-Type Retainer Nylon 18mm
Couldn't load pickup availability
Product Description
• EPDM tube and cover• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Technical Specifications
| Item#: | 99675 |
|---|---|
| Type | Coolant Hose |
| I.D. | 1/2 " |
| Hose O.D. | 25/32 " |
| Bend Radius | 2-1/2 " |
| Working Pressure | 125 PSI |
| Burst Pressure | 500 PSI |
| Length | 10 ft |
| Recommended Hose Clamp | 86724 |
| Description | To be Discontinued - No volume |
| UNSPSC #: | 25170000 |
| TAA Compliant: | Yes |
| Weight: | 3.0 lb |
Product Restrictions
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
