Coolant Hose, 1/2" ID, 25/32" OD, 10' Length, 2-1/2" Bend Radius, 125PSI
(Pack of
1)
SKU:99675 Item#: 99675
• EPDM tube and cover
• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Couldn't load pickup availability
Catalog page#: 7-10
Frequently Bought Together
Brass Fuel Line Male Pipe Elbow 90° 3/8"
Couldn't load pickup availability
Silicone Heater and Radiator Hose 1-15/16" OD
Couldn't load pickup availability
Fuel Injection Hose 3/8" x 10'
Couldn't load pickup availability
DOT Compression Elbow Male 90° Brass 3/8 x 3/8"
Couldn't load pickup availability
DOT Compression Union Brass 1/2"
Couldn't load pickup availability
Super 77 Hose Clamp SS 2 to 2-7/8"
Couldn't load pickup availability
Standard Heater Hose 1/2" ID x 50' Black
Couldn't load pickup availability
Fuel Line Hose 3/16" ID x 25'
Couldn't load pickup availability
Norma Torro European Hose Clamp 1-13/16 to 1-3/4"
Couldn't load pickup availability
DOT Compression Connector Male Brass 3/8 x 3/8"
Couldn't load pickup availability
DOT Elbow Male 90° Brass 5/8 x 1/2-14
Couldn't load pickup availability
Slotted Hex Head Hose Clamp 301 SS 7/16 to 1"
Couldn't load pickup availability
Fender Liner Screw Grommet Nylon M5.5
Couldn't load pickup availability
Phillips Truss Head Sheet Metal Screw Steel 15mm
Couldn't load pickup availability
Push-Type Retainer Nylon 20mm
Couldn't load pickup availability
Product Description
• EPDM tube and cover• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Technical Specifications
| Item#: | 99675 |
|---|---|
| Type | Coolant Hose |
| I.D. | 1/2 " |
| Hose O.D. | 25/32 " |
| Bend Radius | 2-1/2 " |
| Working Pressure | 125 PSI |
| Burst Pressure | 500 PSI |
| Length | 10 ft |
| Recommended Hose Clamp | 86724 |
| Description | To be Discontinued - No volume |
| UNSPSC #: | 25170000 |
| TAA Compliant: | Yes |
| Weight: | 3.0 lb |
