Wire Thread Insert Repair Kit 10-32
(Pack of
1.0)
• Helically-wound thread repair – universally accepted and most cost-effective method of thread repair
• Manufactured from precision cold-formed 18-8 (Type 304) stainless steel
• Kits contain tap, inserts, installation tool, tang removal tool (select kits) and instructions, packaged in a sturdy and convenient storage box
• Inserts compensate for pitch and angle errors and share the load over more of the thread for stronger assemblies
• Tensile strength of at least 200,000 PSI
• Wide effective temperature range: –275°F to +774°F (–170°C to +412°C)
Fix-A-Thred® Insert Installation Instructions
Drill to clear out the damaged thread (if necessary).
Thread insert tap supplied. Tap thread should match up with bolt.
Wind insert in with light downward pressure until 1/4 to 1/2 turn below surface, driving tang towards bottom of the hole.
Remove tool and sit back on top of tang. Tap down sharply. Do not try to twist tang off. For large fine threads, use long nose pliers and pull tang out.
To insure proper installation of inserts, always use the correct and corresponding tools.
Couldn't load pickup availability
California Proposition 65: WARNING: Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
Frequently Bought Together
E-Z Kut Reinforced Abrasive Wheel 3"
Couldn't load pickup availability
Abrasive Bristle Wire Belt Steel 23mm
Couldn't load pickup availability
Polymer Wheel Rubber Eraser 30mm
Couldn't load pickup availability
Specialty Rivet with Plastic Cap Aluminum 3.2mm
Couldn't load pickup availability
Rocker Molding Clip with Sealer Nylon Blue 17mm
Couldn't load pickup availability
Rocker Panel Molding Clip Nylon White 12 x 20mm
Couldn't load pickup availability
Micro Screw Power Extractor Number 10 to 12
Couldn't load pickup availability
Thread Gauge 44 - 8 Pitch 44 To 8
Couldn't load pickup availability
Extractor Kit
Couldn't load pickup availability
Wire Stripper-Cutter 6" Stainless Steel Jaws
Couldn't load pickup availability
Hex Key Set, Balldriver, Ball Hex, 9pc
Couldn't load pickup availability
Razor Blade Single Edge w/Notch
Couldn't load pickup availability
Wire Thread Insert Repair Kit M16-1.5
Couldn't load pickup availability
Wire Thread Insert Repair Kit 7/8-9
Couldn't load pickup availability
Wire Thread Insert Repair Kit 1-14
Couldn't load pickup availability
Product Description
• Helically-wound thread repair – universally accepted and most cost-effective method of thread repair• Manufactured from precision cold-formed 18-8 (Type 304) stainless steel
• Kits contain tap, inserts, installation tool, tang removal tool (select kits) and instructions, packaged in a sturdy and convenient storage box
• Inserts compensate for pitch and angle errors and share the load over more of the thread for stronger assemblies
• Tensile strength of at least 200,000 PSI
• Wide effective temperature range: –275°F to +774°F (–170°C to +412°C)
Fix-A-Thred® Insert Installation Instructions
Drill to clear out the damaged thread (if necessary).
Thread insert tap supplied. Tap thread should match up with bolt.
Wind insert in with light downward pressure until 1/4 to 1/2 turn below surface, driving tang towards bottom of the hole.
Remove tool and sit back on top of tang. Tap down sharply. Do not try to twist tang off. For large fine threads, use long nose pliers and pull tang out.
To insure proper installation of inserts, always use the correct and corresponding tools.
Technical Specifications
| Item#: | 53833 |
|---|---|
| Type | Insert Repair Kit |
| Size | 10-32 |
| Recommended Drill Size | 13/64 " |
| Number of Pieces | 17 |
| UNSPSC #: | 27112810 |
| TAA Compliant: | Yes |
| Weight: | 0.46 lb |
Product Restrictions
California Proposition 65: WARNING: Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
