Wire Thread Insert Repair Kit, 17 Pieces, 4-40, 304 Stainless Steel, 200000PSI Tensile Strength
(Pack of
1)
• Helically-wound thread repair – universally accepted and most cost-effective method of thread repair
• Manufactured from precision cold-formed 18-8 (Type 304) stainless steel
• Kits contain tap, inserts, installation tool, tang removal tool (select kits) and instructions, packaged in a sturdy and convenient storage box
• Inserts compensate for pitch and angle errors and share the load over more of the thread for stronger assemblies
• Tensile strength of at least 200,000 PSI
• Wide effective temperature range: –275°F to +774°F (–170°C to +412°C)
Fix-A-Thred® Insert Installation Instructions
Drill to clear out the damaged thread (if necessary).
Thread insert tap supplied. Tap thread should match up with bolt.
Wind insert in with light downward pressure until 1/4 to 1/2 turn below surface, driving tang towards bottom of the hole.
Remove tool and sit back on top of tang. Tap down sharply. Do not try to twist tang off. For large fine threads, use long nose pliers and pull tang out.
To insure proper installation of inserts, always use the correct and corresponding tools.
Couldn't load pickup availability
California Proposition 65: WARNING: Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
Frequently Bought Together
Aluminum Oxide Grain Locking Grinding Disc 2"
Couldn't load pickup availability
Steel Crimped End Brush 1/2"
Couldn't load pickup availability
Cryobit 1/4" Dia. Maintenance Drill Bit , 135o Split Point, W/ Flats
Couldn't load pickup availability
Miniature Incandescent Bulb 12V 2CP
Couldn't load pickup availability
Front/Rear Bumper Push-Type Retainer Nylon 20mm
Couldn't load pickup availability
Fender Splash Shield Push Rivet Nylon 7mm Hole
Couldn't load pickup availability
Rethreading Die M10 x 1.5
Couldn't load pickup availability
Thin Wall Locking Thread Repair Insert Kit 1/4"
Couldn't load pickup availability
Broken Bolt Power Extractor Kit 4Pcs
Couldn't load pickup availability
Polymer Wheel Rubber Eraser 30mm
Couldn't load pickup availability
Large Index-Tend Pry Bar
Couldn't load pickup availability
Cordless Right Angle Grinder Charging Bundle
Couldn't load pickup availability
Wire Thread Insert Repair Kit 7/16-14
Couldn't load pickup availability
Wire Thread Insert Repair Kit 7/16-20
Couldn't load pickup availability
Wire Thread Insert Repair Kit M6-1
Couldn't load pickup availability
Product Description
• Helically-wound thread repair – universally accepted and most cost-effective method of thread repair• Manufactured from precision cold-formed 18-8 (Type 304) stainless steel
• Kits contain tap, inserts, installation tool, tang removal tool (select kits) and instructions, packaged in a sturdy and convenient storage box
• Inserts compensate for pitch and angle errors and share the load over more of the thread for stronger assemblies
• Tensile strength of at least 200,000 PSI
• Wide effective temperature range: –275°F to +774°F (–170°C to +412°C)
Fix-A-Thred® Insert Installation Instructions
Drill to clear out the damaged thread (if necessary).
Thread insert tap supplied. Tap thread should match up with bolt.
Wind insert in with light downward pressure until 1/4 to 1/2 turn below surface, driving tang towards bottom of the hole.
Remove tool and sit back on top of tang. Tap down sharply. Do not try to twist tang off. For large fine threads, use long nose pliers and pull tang out.
To insure proper installation of inserts, always use the correct and corresponding tools.
Technical Specifications
| Item#: | 61222 |
|---|---|
| Type | Insert Repair Kit |
| Size | 4-40 |
| Recommended Drill Size | No. 31 |
| Number of Pieces | 17 |
| UNSPSC #: | 27112810 |
| TAA Compliant: | Yes |
| Weight: | 0.44 lb |
Product Restrictions
California Proposition 65: WARNING: Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
