Expansion Shield Anchor, 1/2" Drill Size, 1/4"
(Pack of
25)
SKU:96958 Item#: 96958
• Evenly distributed four-way expansion of anchor wall by internal nut
• Excellent holding power in concrete, brick, stone and cinder block
• Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
• Meets GSA Specification FF-S-325 3.2.2.2.1.3
• Use for anchoring medium and heavy loads in solid and hollow-base materials
• Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Frequently Bought Together
Masonry Anchor Phillips Head #14-10 x 2-3/4"
$0.00
Couldn't load pickup availability
Drop-In Anchor Steel 1/2 x 2"
$0.00
Couldn't load pickup availability
Masonry Anchor Hex Washer Head Steel 5/16 x 1-3/4"
$0.00
Couldn't load pickup availability
Double Expansion Shield Anchor Alloy Steel 3/4"
$0.00
Couldn't load pickup availability
Pin Drive Expansion Anchor Steel 5/16 x 4"
$0.00
Couldn't load pickup availability
Expansion Shield Anchor Alloy Steel 1/2"
$0.00
Couldn't load pickup availability
USS Flat Washer Thru-Hardened Steel 1/4"
$0.00
Couldn't load pickup availability
DIN 9021B Fender Washer Low Carbon Steel 18mm
$0.00
Couldn't load pickup availability
Hex Nut Grade 8 Steel 3/8-16
$0.00
Couldn't load pickup availability
Front Bumper Push-Type Retainer Nylon 10mm
$0.00
Couldn't load pickup availability
Fender Lining Screw Grommet Nylon #12
$0.00
Couldn't load pickup availability
Phillips Truss Head Sheet Metal Screw Steel 15mm
$0.00
Couldn't load pickup availability
Product Description
• Evenly distributed four-way expansion of anchor wall by internal nut• Excellent holding power in concrete, brick, stone and cinder block
• Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
• Meets GSA Specification FF-S-325 3.2.2.2.1.3
• Use for anchoring medium and heavy loads in solid and hollow-base materials
• Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Technical Specifications
| Item#: | 96958 |
|---|---|
| Anchor Size | 1/4 " |
| Type | Forway Expansion Shield Anchor |
| Drill Size | 1/2 " |
| 3,000 PSI Concrete Shear Strength | 2,100 lb |
| Tensile Block | 1,925 lb |
| Thread Pitch | 20 |
| 3,000 PSI Concrete Tensile Strength | 2,320 lb |
| UNSPSC #: | 31162101 |
| TAA Compliant: | Yes |
| Weight: | 0.68 lb |
